Skip to content

Paper crown template

Print a plain crown front and three extension bands to colour, cut and join.

Paper crown front: six flat peaks and a shaded joining endJOINCROWN FRONT
The printable front is 180 × 75 mm. The shaded end is for joining.

Print the crown and bands

Download the free two-page A4 paper crown PDF. Page 1 has the front and three matching bands. Page 2 has the joining and fitting guide. Print just page 1 if you will follow the instructions here.

Choose A4 portrait at Actual size or 100%. Measure the check line: it should be 50 mm. Use paper or light card that your printer accepts, colouring pens or crayons, scissors and tape. Ask an adult to help with cutting and fitting.

The front has a continuous 30 mm band beneath the points. The three extension strips are each 180 × 30 mm, with a shaded 20 mm end. Use only the strips you need; shorten them or print extra copies to change the length.

See an extension band and the first join
Paper extension band with a shaded joining endJOINEXTENSION BAND
One of three identical bands. Keep its shaded joining end when cutting it out.
First join: an extension band lies behind the crown frontJOINEXTENSION BANDJOINCROWN FRONT
Lay a band’s shaded end behind the front’s plain end, overlapping the full shaded area. The pieces stay flat.

How to make the paper crown

1. Decorate, then cut

Colour the front while it is still on the sheet. Add a name, a pattern or your own drawings. Colour the bands too if you want them to match.

Cut around the outside solid outlines. Keep the shaded ends attached. There are no inside cuts or folds.

2. Join the bands flat

Keep the printed side facing out. Put a band’s shaded end under the plain end of the crown front, overlapping the full 20 mm shaded width. Tape across the join.

Add another band in the same way if you need more length: shaded end underneath, plain end on top.

Join close-up: the next strip overlaps underneath by 20 mm20 mm overlapPrevious pieceNext strip
A close-up of one join. The pale area marks the 20 mm overlap; it is covered when the pieces are joined. Tape over the seam.

3. Mark a loose fit

With adult help, hold the open crown loosely around the wearer’s head. Let the front’s shaded end sit underneath the last band’s plain end, then mark where that final join should be.

Take the crown off before trimming or taping it. Use the wearer’s actual fit, rather than a fixed age or head-size guide. Keep it clear of the eyes.

4. Take it off and fasten

Remove the crown and trim spare length from the final plain band end. Leave enough paper for the overlap. Put the front’s shaded end underneath and tape the final joint.

If the strip needs to overlap further for a smaller crown, cover that extra overlap too. For a longer crown, add another band before closing it. Use tape, without staples or ties.

5. Check and adjust

Try it on again. If it feels tight, slips down or is uncomfortable, take it off and change the band length. You can also make it for a toy: measure that toy and use fewer or shorter bands.

Questions about the template

Can I print just the cutting page?

Yes. Page 1 has the crown front and all three bands. Page 2 has the illustrated guide. Both pages include a 50 mm print check.

Do I have to use all three bands?

No. Join enough to go loosely around the wearer, then check and mark the final overlap. Trim spare plain band length after taking the crown off. Print another copy of page 1 if more bands are needed.

Can I make it without a printer?

Draw a 180 × 75 mm rectangle. Mark a horizontal line 30 mm above its bottom edge: this is the uncut base band. Divide the top edge into six 30 mm sections. In each section, mark a 6 mm flat peak centred at the top, then join its ends diagonally to the base-band line at the section’s edges. Cut around the resulting outside shape.

Draw extra strips 30 mm wide. Mark a 20 mm joining zone at one end of each strip and at the left end of the front’s base band. Follow the same joining and fitting steps.

Can I leave the crown blank?

Yes. The front has no fixed theme, gems or character picture. Add your own drawing or use plain coloured paper.

More things to make

Make our four paper finger puppets, or cut and join a small paper basket. The free printable library has the full collection.

The separate front and fitted paper-band method is also used in the Eden Project Communities crown activity. These plain templates, dimensions, diagrams and page layouts are original KidsCo resources, free to print for home, classroom and club use. Please share this page’s link rather than selling or re-uploading the PDF.

Related Posts