Skip to content

Paper boat template

Print a rectangle, then fold a classic paper boat.

Classic paper boat: schematic side view from the final folding stepBoat · schematic side view
The shape at the last step, shown as a side-view diagram.

Print the template and fold guide

Open the free four-page A4 paper boat PDF. The pages have different jobs:

  • Page 1: the wave-decorated cutting rectangle.
  • Page 2: the centre crease, half-fold and top corners.
  • Page 3: the brim folds, first diamond and lower points.
  • Page 4: the second diamond and the final opening.

Print page 1 to fold, and keep the guide beside it. You can also read the same steps below.

Cut out the rectangle first

Use ordinary A4 printer paper, print one-sided in portrait and choose Actual size or 100%. The check line should measure 50 mm. Adjust the scaling setting if it prints at a different length.

An adult cuts around the solid outside border to make a 180 × 250 mm rectangle. Fold that rectangle, rather than the whole A4 page. Keep the inside lines intact. The dashed lines mark the first two creases; the waves are decoration.

Once the rectangle is cut, the folds need no more scissors, glue or tape. If you have no printer, an adult can measure and cut a plain 180 × 250 mm paper rectangle instead.

How to fold the paper boat

Start with the printed side down. Match the edges before pressing each crease. The pictures show the paper before and after each action.

1. Make a centre crease

Start with the printed side down. Bring the long edges together, press the centre crease, then open the rectangle flat.

1. Make a centre creaseFold long edges togetherOpen again
Open the first crease before making the half-fold.

2. Fold in half

Bring the top short edge down to the bottom short edge. The folded edge is at the top; the open edges are at the bottom.

2. Fold in halfTop edge comes downOpen edges at the bottom
The two open short edges stay at the bottom.

3. Bring the top corners in

Bring both top corners to the middle crease. Match the edges. Leave the two rectangular brim strips below the triangle.

3. Bring the top corners inFold both top cornersPoints meet at the middle
The rectangular strips below the triangle become the brims.

4. Tuck the corners and lift the brims

On the front, tuck in the brim corners, then lift that brim up. Turn over. Tuck the other corners in and lift that brim too.

4. Tuck the corners and lift the brimsBeforeTuck the brim cornersLift both brims
The three pictures separate the corner tucks from the brim lift. Repeat on the back.

5. Open and flatten

Open the bottom of the hat. Bring its two side corners together and flatten it into a diamond. Keep the loose flaps at the bottom.

5. Open and flattenOpen the bottom of the hatFlatten into a diamond
The hat opens at its bottom. Flatten the opening in the other direction to make a diamond.

6. Lift the lower points

Lift the bottom point of the front layer to the top point. Turn over and do the same with the other bottom point.

6. Lift the lower pointsBring the lower point upTurn over and repeat
Both lower points come up, one on each side.

7. Open once more

Open the bottom of the triangle. Bring its side corners together and flatten it into a smaller diamond.

7. Open once moreOpen the bottom againA smaller diamond
Open and flatten again to make the smaller diamond.

8. Pull the points apart and open the hull

Find the two loose points at the top. Pull one left and one right. Ease the bottom open to shape the hull.

8. Pull the points apart and open the hullTwo loose points at the topBoat · schematic side view
Pull the two loose top points apart. The finished boat is shown as a schematic side view.

If a fold gets stuck

The hat will not open: go back to step 4 and find the gap between its two bottom edges. Open from that gap, keeping the top point joined.

The last diamond will not pull apart: check that you have found the two loose points at the top. Ease them apart gently. Flatten the paper and check steps 6 and 7 again if needed.

Give the boat a name or add it to a tabletop scene. You can draw details after folding, using the wave pattern as part of the decoration.

More things to make with paper

For another folding project, use our classic Dart paper aeroplane sheets or paper fortune teller template. Our paper games use a pencil and simple boards.

The pattern, diagrams and page layouts here are original KidsCo resources, free to print for home, school and club use. Please share this page’s link rather than selling or re-uploading the PDF.

This is a traditional folded boat. Tower Bridge also has an illustrated classic boat guide, with a key to its folding symbols.

Related Posts